Fineness modulus of fine aggregate varies from 2.0 to 3.5mm. Fine aggregate having fineness modulus more than 3.2 should not considered as fine aggregate. Various values of fineness modulus for different sands are detailed below. Type of sand Fineness modulus range Fine sand 2.2 – 2.6 Medium sand 2.6 – 2.9 Coarse sand 2.9 – 3.2
The optimization phase consisted of sieving the crusher fines and mixing different fractions of crusher fines with the natural sand in different combinations to get desired sand gradation.
Jul 30 2016What Is Fineness Modulus of Sand Fineness modulus of sand fine aggregate is an index number which represents the mean size of the particles in sand. It is calculated by performing sieve analysis with standard sieves. The cumulative percentage retained on each sieve is added and subtracted by 100 gives the value of fineness modulus.
Jun 05, 2013 Materials – Aggregate – Classes Aggregate is a collective term for the mineral materials such as sand, gravel … Rather than list WSDOT specifications for each test in their respective ….. common gradation description for fine aggregate is the fineness modulus. …. The amount of fines generated is measured and the result is reported as a degradation factor.
Silica sand was historically used and consistently produced for golf courses, glassmakers and some industrial consumers. Then, in about 2010, demand dramatically increased as oil and gas producers discovered the durable, crush-resistant material. Overnight, frac sand …
DIVIDE & CONQUER. The classification process uses water, gravity and settling principles to separate sand or other bulk materials into similar mesh sizes. After sizing the sand, classifying tanks — for example — are capable of reblending the material to a precise, high-dollar specification. Superior offers a full line of classifying equipment.
M-Sand(Manufactured Sand) as a silt content of around 0.2 percent and water absorption of 1.6 percent, as compared to 0.45 percent and 1.15 percent respectively in river sand. This sand alternative of river sand/natural sand. M-sand(Manufactured Sand) cheaper sand as per river sand. Also, read: What Is Bulkage of Sand (Fine Aggregate ) M-Sand Bonding Strength.
04 Jaw Modules 05 Cone Modules 06 Horizontal Screen Modules 07 Surge Bins Contents Portable Plants 10 Jaw Plants 11 Tracked Jaw Crusher 12 Closed Circuit Cone/ Screen Plants 13 Open Circuit Cone Plants 14 Tracked Cone Crusher 15 Horizontal Shaft Impactor Plants ... sand and gravel, ore and industrial minerals. We provide Modular and Portable ...
MXS Sand Washer is commonly known as wheel-bucket type sand washer. It is developed and produced by Meilan through adopting domestic and overseas advanced technologies and combining the actual situation of domestic aggregate industry. It is usually used with the sand maker.
The sand must have cubicle particles for all sieve sizes and must be washed. Materials which can be crushed to make sand are limestone, granite, basalt, gravel, andesite, sandstone, silica, quartzite. In short, and any sound stone used for construction material can be crushed to produce sand.
Jul 31, 2016 Calculation of Fineness Modulus of Sand. Let us say the dry weight of sample = 1000gm After sieve analysis the values appeared are tabulated below. Therefore, fineness modulus of aggregate = (cumulative % retained) / 100 = (275/100) = 2.75 Fineness modulus of fine aggregate is 2.75. It means the average value of aggregate is in between the 2 nd ...
Jan 01, 2016 Combinations of sand and crusher fines mix Various fractions of crusher fines were added to the original sand samples in various percentages and optimized sand samples were than tested for the improved gradation and improved fineness modulus. These improved versions of results were then compared with the ASTM specified limits.
The bigger the fineness modulus is, the more coarse the sand is. The fineness modulus of the sand used in ordinary concrete is within 3.7 ~ 1.6.And if M x is within 3.7 ~ 3.1, it is coarse sand; if M x is within 3.0 ~ 2.3, it is medium sand; if M x is within 2.2 ~ 1.6, it is fine sand; and if M x is within 1.5-0.7, it is superfine sand which should be considered specifically when concrete is ...
LATEST NEWSOUR LATEST NEWS